How to prepare your car for primer. diy auto body and how to primer a car
In this episode I will teach you how to prepare your car for primer.
how to evaluate the car for dents, what sandpaper should be used for the situation , what steps to take in order to gets the best possible results for you paint job.
Thanks for watching! If you have questions or comments leave them below !
To increase your knowledge and build your skill SUBSCRIBE to the channel and check out my other videos!!!
Disclaimer as an Amazon Associate I earn a small commission (at no additional cost to you) from qualified purchases. I will not recommend any product that I do not use personally.
My amazon affiliate store : Tools and materials are organized into categories .
CLICK HERE
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️
CHEN REFINISH Premium Quality Black 2-3/4″ x 5″ Rubber Sanding Block
Dura-Block AF4405 Black Scruff Pad
3M 05777 Hookit 6″ x 1/2″ x 3/4″ Soft Interface Pad
3M 31435 Stikit Gold 6-inch P320A Grit Disc
3M 03020 Imperial Wetordry 3-2/3″ x 9″ P600 Grit Sandpaper
primer gun 2.0mm nozzle with regulator
Optex polyester primer color change
Optex primer catalyst fast
Speedkote 2k urethane primer kit fast dry
Speedkote epoxy primer quart kit
sem self etching primer
sem aerosol primer
Bondo Gray Filler Primer, Highly Durable & Easy to Use, 11 oz, 1 Aerosol
Kleanstrip Prep-All Wax & Grease Remover, Gallon (KLE-GSW362)
To increase your knowledge and build your skill check out my other how to videos and don’t forget to subscribe to the channel!
Be sure to check out my other videos in the links below!
⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️⬇️
Things that will ruin your diy paint job
How to repair cracked paint on your car
How to repair fiberglass
Disclaimer:
Due to factors beyond the control of Garage Noise, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Garage Noise assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any of my repair video’s. Due to factors beyond the control of Garage Noise, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again Any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Garage Noise.
Likes: 2577
Views: 162920
With which paper should the base coat be sanded before warnishing with colorless warnish?
so you have to always sand primer before painting ?
Can the New base coat be sanded before clear coat?
If bare metal why can’t one just media blast it then primer? Assuming body panels are straight
Excellent videos. My 01 Silverado the clear coat is gone on all the tops were the sun beats down on them.Only edges are flaky and chalky. Do I have to sand off all the clear coat or just feather the edges. What about the clear on the side of fenders,doors, and bed do I scuff them with 320 for primer.
Just subscribed. Should I sand to bare metal if I have rust and crows feet?
What kind of primer paint can is that you used
Very helpful videos!! Here in Atlanta everybody is using Multifiller express from Roberlo Brand, is a high built 2k primer DTM (direct to Metal) so no need to spray a self etching primer first . Thanks for your videos
Looked like you did not have much overspray? How’d you do that ?
I believe the box sides are polyurethane on a stepside. I have the same truck.